How to Adjust a TaylorMade Qi4D Driver (Adjustment Guide)

Want to know how to adjust a TaylorMade Qi4D driver to change loft and lie angles? We have a complete guide and adjustment table.

The TaylorMade Qi4D driver series is new for 2026 and is fully adjustable with a Hosel that gives you the ability to adjust the loft to increase or decrease your launch angle.

Driver adjustment amounts differ from brand to brand, but the step-by-step plan below shows how the TaylorMade Qi4D drivers can be adjusted.

TaylorMade Qi4D Driver Lofts

The TaylorMade Qi4D driver and the Max models are sold in three standard lofts of 9 degrees, 10.5 degrees and 12 degrees.

The LS driver has lofts of 8 degrees, 9 degrees and 10.5 degrees.

TaylorMade Qi4D driver specifications

Attic: 9 degrees, 10.5 degrees and 12 degrees (left-handed 9 degrees and 10.5 degrees)

Standard length: 45.75 inches

Standard lie: 56-60 degrees

Adjustability: Plus 2 degrees or minus 2 degrees (7-11 degrees, 8.5-12.5 degrees and 10-14 degrees)

TaylorMade Qi4D Max driver specifications

Attic: 9 degrees, 10.5 degrees and 12 degrees (left-handed 9 degrees and 10.5 degrees)

Standard length: 45.75 inches

Standard lie: 58-62 degrees

Adjustability: Plus 2 degrees or minus 2 degrees (7-11 degrees, 8.5-12.5 degrees and 10-14 degrees)

TaylorMade Qi4D LS driver specifications

Attic: 8 degrees, 9 degrees and 10.5 degrees

Standard length: 45.75 inches

Standard lie: 54-58 degrees

Adjustability: Plus 2 degrees or minus 2 degrees (6-10 degrees, 7-11 degrees and 8.5-12.5 degrees).

Adjusting the Loft Angle of a TaylorMade Qi4D Driver

There are a few simple steps you can take to adjust the loft angle of your driver. All you need is an adjustment tool or a wrench to get started.

Here’s how to customize a TaylorMade Qi4D driver:

1. Locate the screw on the sole of your TaylorMade Qi4D driver that secures the driver head to the shaft.

2. Using the wrench, loosen the screw by turning counterclockwise.

3. Once the screw is fully loosened, you can rotate the adjustable hose to a lower cage or a higher cage depending on your preference. You will notice the loft figure you had the driver set to and you can rotate the shaft to up to 16 other options.

The available options are:

• Standard (STD): Standard setting with indicated loft, a square face angle and a standard lie angle
• Higher: Increases loft by up to +2°, closes the face by 4° and increases spin for a higher ball flight.
• Lower: Reduces loft to -2°, opens the face by 4° and reduces spin for a lower ball flight.
• Upright: Maintains the stated loft but increases the lie angle by 4°, which promotes a draw bias.
• Average settings: The Hosel allows 12 positions, with incremental adjustments of 0.5°-0.75° in loft and lie angle, and 1°-2° in face angle

4. When you have rotated the hosel to the desired loft, slide the shaft back into your club head. Your new loft will be visible through the window to most drivers.

5. Replace the screw and tighten it clockwise with the wrench. When it is completely tight, you will hear a crank that sounds like the driver is creaking. At this point the screw is tightened as much as necessary.

Each time you want to adjust the hutch, repeat this process.